Hello, welcome to visit the home page of Jinan Ruby Laser Technology Co.,Ltd!

Products

Contact Us

Phone : +86 0531-85908792

Email:Admin:zrsuns@outlook.com          Sales:sales@rlaserpowersupply.com

Skype: ZRsunslaser

Q     Q: 2407603284

Mobile :+86-13295411923

微信

  • ZR-100W CO2 laser power supply
  • ZR-100W CO2 laser power supply
  • ZR-100W CO2 laser power supply
  • ZR-100W CO2 laser power supply
  • ZR-100W CO2 laser power supply
  • ZR-100W CO2 laser power supply
  • ZR-100W CO2 laser power supply
  • ZR-100W CO2 laser power supply
  • ZR-100W CO2 laser power supply
  • ZR-100W CO2 laser power supply
  • ZR-100W CO2 laser power supply

ZR-100W CO2 laser power supply

1.This external potentiometer laser psu box selects H/L/P/G/IN/5V green terminal board to accept laser control signal and it has aluminum upper cover and base, galvanized sheet shell..

2.This external potentiometer laser psu box can adopts external LCD digital display module by network cable,which can show constant current laser power driving units working current,working statues and failure code. It is very good function for both machine factory and machine users

3.The 150w laser psu box adopts one PCS fan for cooling. It use two Taiwans bearing which make the fan runs for very long time.


Order online

ZR-100W CO2 laser power supply

Feature

1. Input analog signal(0~5V) or PWM is selected to control the output laser power on this 100w laser power supply unit.

2. The 100w laser power supply unit has H/L/P/G/IN/5V control signal interfaceThe upper cover and bottom shell are aluminum Casing is made of galvanized sheet.

3.The air cooling laser power supply unit's control interface is applicable to high/low level signal. TTL level is to control the on/off of the laser power with a protective switch to check water-flow and ventilation.

4. The 100w laser power supply unit can match with EFR,SPT,Yongli, Weiju and other brands' 140-145cm sealed glass type CO2 laser lamp. The external LCD laser power supply unit selects zero-current half-bridge soft-switch circuit to make sure the air cooling laser power supply unit has high efficiency and fast response speed.

5.This laser engraving power supply unit can use an external LCD module. It can display common fault codes, output current and working status. It is helpful for operators to understand the working state of 100w laser power supply unit and solve problems quickly. In addition, the output current can also be changed by the rotating potentiometer of the LCD module.

6.This100w laser power supply unit is equipped with two cooling fans. Better heat dissipation can protect the internal electronic components of this power supply.

7.This air cooling laser power supply unit has RED TEST button to easily figure out CO2 power supplies or CO2 laser tube's failure. It is very easy and simple to remove trouble.

8.Each external LCD laser power supply unit before selling will go through the aging check:

(1) sustain 10 hours at temperature 60 Degrees Celsius under full-load condition;

(2) 500 times on/off check for 7 seconds.

9.The 100w laser power supply unit is well grounded, which can ensure the safety of operators. At the same time, the air cooling laser power supply unit also has an open circuit protection function, which allows the external LCD laser power supply unit to work for a short time in the open circuit state.

Specification

lnput 

Input voltage

AC220V±10% (AC110V specified while order)


AC frequency

47~440HZ


Maximum input power

770W


Maximum input current

3.5A

Output

Maximum output voltage

35KV


Maximum output current

33mA

(depending on the laser tubes of different manufacturers)

Efficiency

More than 90% (Full load)

Response speed

Not more than 1ms

Control lnterace

TTL multilevel switching control,effective level can be high and low selection (see control wining diagram)

Insulation

lnput-output

AC 1500V 1 minutes not more than 10mA


lnput-shell

AC 1500V 1 minutes not more than10mA


Output-shell

Connection

Open Circuit Protection

Can be short circuit (requires a good grounding shell,while avoiding the positive electrode and the shell between the arc)

Environmental Requested

Working temperature

-10~50


Storage of temperature

-20~75


Relative Humidity

Maximum 85%RH (non-condensing)


Altitude

100,000 feet of work

200,000 feet of storage,dose not work

Cooling methods

Forced air cooling (fan cooling)

Dimensions (LxWxH)

305mmx205mmx112mm


Get the latest price? We'll respond as soon as possible(within 12 hours)
Welcome to Consult
Telephone contact

TELEPHONE

+86-539-8058588

MOBILE PHONE

086-13295411923

WECHAT
CHAT