Hello, welcome to visit the home page of Jinan Ruby Laser Technology Co.,Ltd!

Products

Contact Us

Phone : +86 0531-85908792

Email:Admin:zrsuns@outlook.com          Sales:sales@rlaserpowersupply.com

Skype: ZRsunslaser

Q     Q: 2407603284

Mobile :+86-13295411923

微信

  • BR-130W CO2 laser power supply
  • BR-130W CO2 laser power supply
  • BR-130W CO2 laser power supply
  • BR-130W CO2 laser power supply
  • BR-130W CO2 laser power supply

BR-130W CO2 laser power supply

1.The 130W CO2 power supply has RED TEST button to easily figure out CO2 power supplies or CO2 laser tubes failure. It is very easy and simple to remove trouble.

2.The 220/110V CO2 power supply has H/L/P/G/IN/5V control signal portThe upper cover and bottom shell are aluminum shell is galvanized sheet.

3.The CO2 power supply on laser cutter is well grounded, which can ensure the safety of operators. At the same time, the 220/110v CO2 power supply also has an open circuit protection function, which allows the CO2 power supply on laser cutter to work for a short time in the open circuit state.


Order online

BR-130W CO2 laser power supply

Feature

1.This130W CO2 power supply is equipped with two cooling fans. Better heat dissipation can protect the internal electronic components of this power supply

2. The 220/110V CO2 power supply has H/L/P/G/IN/5V control signal portThe upper cover and bottom shell are aluminum shell is galvanized sheet.

3.Each CO2 power supply on laser cutter  before selling will go through the aging check:

(1) sustain 10 hours at temperature 60 Degrees Celsius under full-load condition;

(2) 500 times on/off check for 7 seconds.

4.The 220/110V  CO2 power supply's control is applicable to high/low level signal. TTL level is to control the on/off of the laser power with a protective switch to check water-flow and ventilation.

5.The 130W  CO2 power supply has RED TEST button to easily figure out CO2 power supplies or CO2 laser tube's failure. It is very easy and simple to remove trouble.

6.The CO2 power supply on laser cutter is well grounded, which can ensure the safety of operators. At the same time, the 220/110v  CO2 power supply also has an open circuit protection function, which allows the CO2 power supply on laser cutter to work for a short time in the open circuit state.

7.Input analog signal(0~5V) or PWM is used to control the output laser power on this 130W  CO2 power supply.

8.The 130W CO2 power supply can match with EFR,Yongli,SPT, Weiju and other factories'160-165cm 130W sealed glass type CO2 laser tube. The 220/110V CO2 power supply uses zero-current half-bridge soft-switch circuit to make sure the CO2 power supply on laser cutter has high efficiency and fast response speed.

9.The 130W CO2 power supply can use an external LCD module. It can display common fault codes, output current and working status. It is helpful for operators to understand the working state of 220/110V  CO2 power supply and solve problems quickly. In addition, the output current can also be changed by the rotating potentiometer of the LCD module.

Specification

Input 

Input voltage

AC220V±10% (AC110V specified while order)

AC frequency

47~440HZ

Maximum input power

970W

Maximum input current

4.3A

Output

Maximum output voltage

40KV

Maximum output current

36mA

(depending on the laser tubes of different manufacturers)

Efficiency

More than 90% (Full load)

Response speed

Not more than 1ms

Control lnterace

TTL multilevel switching control,effective level can be high and low selection (see control wining diagram)

Insulation

lnput-output

AC 1500V 1 minutes not more than 10mA

lnput-shell

AC 1500V 1 minutes not more than10mA

Output-shell

Connection

Open Circuit Protection

Can be short circuit (requires a good grounding shell,while avoiding the positive electrode and the shell between the arc)

Environmental Requested

Working temperature

-10~50

Storage of temperature

-20~75

Relative Humidity

Maximum 85%RH (non-condensing)

Altitude

100,000 feet of work

200,000 feet of storage,dose not work

Cooling methods

Forced air cooling (fan cooling)

Dimensions (LxWxH)

335mmx205mmx100mm


Get the latest price? We'll respond as soon as possible(within 12 hours)
Welcome to Consult
Telephone contact

TELEPHONE

+86-539-8058588

MOBILE PHONE

086-13295411923

WECHAT
CHAT